烏魯木齊軟膜天花龍骨安裝工藝詮釋

第一步：軟膜天花龍骨安裝

The first step: piamater ceiling keel installation

根據圖紙?jiān)O(shè)計要求，在需要安裝軟膜天花的水平高度位置四周圍固定一圈4X4Cm支撐龍骨(有些地方面積比較大時要求分塊安裝,以達到良好效果.這樣就需要中間位置加一根木方條子)。

According to the requirements of design drawings, the position of the height level around the need to install piamater ceiling around a ring of 4X4Cm fixed support keel (some local area is large block installation requirements, in order to achieve good results. This requires the middle position plus a wooden note).

當所有需要木方條子固定好之后，然后在支撐龍骨的底面固定安裝軟膜天花的鋁合金龍骨。

When all the required wood sliver fixed, and then in the Aluminum Alloy keel support keel bottom fixed installation soft film ceiling.

第二步軟膜天花安裝：

The second step installation of soft film smallpox:

當所有的安裝軟膜天花的鋁合金龍骨固定好以后，再安裝軟膜。先把軟膜打開用專用的加熱風炮充分加熱均勻，然后用專用的插刀把軟膜張緊插到鋁合金龍骨上，最后把四周多出的軟膜修剪完整即可。

When all the Aluminum Alloy keel installation soft film ceiling fixed after installing film. The film opened with a special heating air full uniform heating, and then use a dedicated knife inserted film tensioning is inserted into the Aluminum Alloy keel, the film can be more around the complete pruning.

安裝完畢后，用干凈毛巾把軟膜天花清潔干凈。

After installation, with a clean towel to clean soft film smallpox.

知識拓展：軟膜天花施工注意事項

The expansion of knowledge: piamater ceiling construction notice

安裝前先到工地現場檢查是否有條件安裝龍骨，現場墻身是否完成，木工部分加工是否合格，需要抹灰部分先完成，特別注意木工部分一定要按照要求來做，燈、風口等開孔尺寸要提前加工好。

Before installation to the site to check whether the conditions of the keel wall, the scene is completed, woodworking processing part is qualified, need to pay special attention to the first part of plastering, carpentry part must be in accordance with the requirements to do, to advance the processing hole size, light air etc..

現場條件許可方進場施工，首先要按圖紙?jiān)O(shè)計要求的木工做好部分進行固定鋁合金龍骨龍骨，注意角位一定要直角平整光滑，駁接要平、密。

Field conditions permit construction, first of all, according to the requirements of the drawing design carpentry do some of the fixed aluminum alloy keel keel, attention to the corner must be flat smooth, and the barge to flat, dense.

注意燈架、風口、光管盤要與周邊的龍骨水平，并且要求牢固平穩不能搖擺方可。

Pay attention to the lamp holder, air port, light tube plate to the level of the surrounding keel, and requires a stable and smooth can not swing.

煙感、吸頂燈，先定位再做一個木底架，木底架底面要打磨光滑，并注意水平高度，太低就容易凸現底架的痕跡。

The smoke, ceiling lamps, the first position to make a wooden frame wooden chassis underside to polish, and pay attention to the level of height is too low, it is easy to show a trace.

安裝天花之前，認真檢查龍骨接頭是否牢固和光滑，噴淋頭要粘上白膠帶，風口要處理好。

Before the installation of smallpox, carefully check the keel joint is firm and smooth, spray head to stick on the white tape, the outlet should be handled well.

安裝天花時要先從中間往兩邊固定，同時注意兩邊尺寸，注意焊接縫要直最后做角位,注意要平整光滑。四周做好后把多出的天花修剪去除。達到完美的收邊效果。

When installing smallpox, should first from the middle to both sides fixed, at the same time pay attention to both sides of the size, pay attention to the welding seam should be straight to the final corner, pay attention to smooth and smooth. Around to do a good job after the removal of the smallpox pruning. To achieve the perfect side effect.

開燈孔要在燈孔的位置上做好記號，把PVC燈圈小心準確地粘在軟膜的底面，待牢固后把多出的天花去除即可。

Turn on the lights to make a mark in the lamp hole hole position, the PVC lamp ring carefully glued to the bottom surface of piamater accurately, to be strong after the removal of smallpox can be.

開風口、光管盤口處理就是找到風口光管盤口的位置，跟做四周一樣，把軟膜安裝到鋁合金龍骨上，注意角位要平整。做好后把多出的天花切除即可。

Open the air inlet, outlet pipe is to find the light position of the light pipe handicap handicap, like around the soft film mounted to Aluminum Alloy keel, note the angle should be smooth. Do a good job after the removal of the smallpox can be more.

最后用干凈毛巾清潔軟膜天花表面。

Finally, with a clean towel to clean the surface of soft film smallpox.

想必大家看完對于以上的知識介紹有了一定的了解，以上就是有關新疆軟膜天花吊頂的一些基本信息，大家可以參考一下，對于理解和參與會有幫助。更多關于該動態，烏魯木齊軟膜天花安裝公司會繼續介紹，歡迎關注！